How to Replace a Kia Sportage Replacement Key
The key of a lot of Kia models has an electronic keyless entry system built into. This key typically resembles an remote control, and can be exchanged with a new one from an Kia dealer or locksmith.
Key fobs might stop working due to a variety of reasons, such as a dead battery, worn-out buttons signals, signal interference or water damage. Here are some tips to help you get your Kia sportage replacement key to work again.
How to replace the remote key or smart key?
Whether your Kia comes with an intelligent key, remote key push-to-start keys, or a standard non-transponder key made of metal The battery inside these keys will eventually need replacing. replacement kia keys www.thekeylab.co.uk is especially the case if your car displays a message indicating that the remote or smart keys aren't powered.
It's a fairly simple process. In order to replace the battery of the key fob remove the mechanical key from the slit in the back of the key fob. Then remove the cover. A small screw is found inside the key fob, which holds the battery in its place. Remove the old battery by unwinding the screw using a small screwdriver. Install the new battery and then close the opening on the key fob.
When the key fob is equipped with a fresh battery Test it by pressing the locks and unlock buttons. If the doors lock and unlock as expected, then you're set! You can now take advantage of the Kia's hands-free lock/unlock feature whenever your fingers feel cold or you have to run some errands in Brandon.
Note: Some key fobs could need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you want to change the programming of your key, you'll need note the key code number on the key code tag.
How do you replace the battery?
If the Kia key fob is unable to respond to pressing the lock or unlock button, it is likely that the battery is insufficient. A low battery may cause other issues, like the check engine light flashing or the engine not cranking properly. Fortunately replacing the key fob battery is a relatively easy DIY project that requires just the most basic tools.
Before beginning the process before beginning the process, ensure that your vehicle is turned off and that all doors are closed. Find the small, metal or plastic piece at the bottom of the key fob. Then, jiggle it until the key pops out. You can then insert this key into the driver's door handle to unlock your car.
To replace the battery inside the key fob, you must remove the cover at the rear. Use a plastic pry tool to remove the latch that holds the black negative cable. Remove the old battery and orient the new one in a way that the "+" positive side is facing your face and the "negative" negative side is facing the fob's metal electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid breaking or bending the steel contacts.
After installing the new battery and turning the key fob on and off in the ignition until the door locks cycle. You can then test the Kia's Key fob again to confirm that it's working as intended.
How can you replace the smart key
You could have an ordinary keyfob or Smart Key, based on the model of Kia Sportage. The difference between them is that the smart fob has an incredibly small key blade tucked inside it, while the standard fob isn't equipped with. Both key fobs come with batteries that will eventually require changing. This is a simple procedure which takes just two minutes.
Before you begin it is essential to make sure that you are on a flat surface with enough lighting and that the Kia is off. Remember that the fob can contain tiny pieces that could fall in the event of a mishap.
The small release button is located on the lower backside. It can be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.
After the key fob has been opened, take out the battery that was in it. The new battery should be a CR-2032, and can be bought online or from your local auto parts store. When you are done it should be possible to lock and unlock your vehicle with your key fob - even if your engine isn't running!
How to replace a mechanical key
The Kia key fob is a great option that lets us lock and unlock our vehicle with the press of a button. Like any other device there are issues with it at times. There are ways to fix these problems and keep your key fobs working for many years.
One of the most common problems is a low or dead battery. The battery could cause the device to stop working or operate intermittently. If this is the case then replace the battery with an entirely new battery.
If this isn't enough to solve the issue, try using an ordinary screwdriver with a flat head to push the plastic casing of the fob open. Be careful not to harm any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a new one.
Once the new battery is in, shut and open the doors with the mechanical key (every kia fob has an emergency mechanical key that can fit in the slot). Test the key fob to check that it's functioning correctly. If the device not working, contact a locksmith or dealer to solve the problem. Make sure they make you an emergency key that functions in all the trunk and door cylinders, to avoid future lockouts.